GreenZ Ultra Finish Polish 4500
GreenZ Ultra Finish Polish 4500 is the next generation of Nano Polish based on latest technology. GreenZ Ultra Finish Polish 4500 contains a micro-fine abrasive particles that quickly removes light imperfections and holograms and provides absolute shine. Absolutely zero dusting and suitable for all gloss paintwork.
GreenZ Car Care introduces a two-step approach for paint correction. In ideal situations, you could remove all paint defects with minimal loss of paint thickness and achieve best gloss in just two-steps and saves lots of time and paint. The secret is our Xtreme Cut 350 can also leave a good finish after an extreme cut, and you can directly go to our UltraFinish Polish 4500 for a final finish. If the paint defects are moderate, you can start with our Heavy Cut Compound 600 and follow our UltraFinish Polish 4500 for a final finish which makes the paint correction a true two-step process.
GreenZ Ultra Finish Polish 4500 is designed for Ceramic Coating with zero silicon fillers and low-oil formula.
The ceramic coating requires clean paint surface to have better chemical bonding between paint molecules and coating molecules, presence of oil or fillers will make coating molecules bonded with them instead of paint molecules and hence the durability of the coating will get affected. Most of the compounds & polishes in the market contains heavy oils which affect the coating durability.
GreenZ Ultra Finish Polish 4500 is a result of a continues improvement and designed for finishing before ceramic coatings. Though GreenZ Ultra Finish Polish 4500 is designed for ceramic paint, the small abrasives work well on conventional clear coats without introducing holograms.
GreenZ Ultra Finish Polish 4500 removes 3000 grit sanding scratches, holograms, compounding haze, light swirls, and mild oxidation. It can be used on brand new finishes or on older, reconditioned paint.
GreenZ Ultra Finish Polish 4500 contains no silicone, waxes, glazes, or fillers. This is a water-based product and less oily which makes it the best finishing polish for the ceramic coating preparation. Wiping will be a breeze.
Application by hand:Mist the Wolfgang German Polish N Wax Applicator with XMT Pad Conditioner to moisten the foam.
Apply a button size amount of GreenZ Ultra Finish Polish 4500 to the applicator.
Work in a back and forth, overlapping motion until the area starts to dry. Wipe off the polish with a damp GreenZ All-Purpose Microfiber Towel. Work in 2 x 2 sq. ft. sections until the entire vehicle is done.
Note: Applying GreenZ Ultra Finish Polish 4500 by hand will enhance the gloss but it will not remove swirls. For paint correction, you must apply this product with a polisher or use any more aggressive polish or compound.
Application by Machine:
Make sure the surface to be polished is clean and dry. Fresh paint should be fully cured. Apply GreenZ Ultra Finish Polish 4500 out of direct sunlight.
Use a soft foam finishing pad, like GreenZ Hybrid Black Finishing Foam Pad. Apply a 6 inch line of compound to the vehicle. With the polisher turned off, spread the polish over about a 2 x 2 sq. ft. area.
Polish at 1200-1800 RPM (5-6 OPM on a dual action polisher) working slowly across and then up and down the area. Check your work after several passes to see if the defects have been removed. If so, reduce the pressure and continue buffing until a high gloss is achieved. If the pad becomes dry, mist it with water and continue buffing.
Wipe the area with a damp microfiber cloth like GreenZ All-Purpose Microfiber Towel.
Always apply a suitable paint protection product such as ceramic coatings, wax or sealant after polishing.
+ Shake well before use each use
+ Always do a test section before using for first time
+ Work on a 2X2 ft. area at a time
In the case of eye contact, immediately flush the eye with plenty of clean water and get a medical attention.
For Skin: Use a suitable barrier cream and wash throughly at the end of each use.
If Swallowed: Do not induce vomiting, visit a physician immediately.
Cut Level: 2/10
Gloss level: 10/10
MADE IN GERMANY
We were using Menzerna 4500 for the finishing for years and we are into ceramic coating. GreenZ Ultra Finish Polish 4500 is an amazing product which provides excellent gloss which never seen before and it's designed for ceramic coating.